![]() If it is bad, you can get a replacement from a number of places or you can go online to the manufacturer’s website to get one. Using a multimeter you can easily check the condition of the fuse. The first thing you want to check is the fuse to see if it is blown.Ī blown fuse will prevent the electric current from flowing into the blender via the power cord when it is plugged into the outlet. You need to open the bottom cover and gain access to the inside of the blender. Once you have found out that it is likely that the problem is inside the blender. If the breaker was not off or tripped, then you should check the outlet with a multimeter to ensure that the outlet is working. If the answer is yes, then you need to do a little more investigating.Ĭheck the electrical breaker that feeds the kitchen outlets. If you try to use your Ninja blender and there is no power indicator light on you should always check the obvious thing first, is it plugged in? While this may seem like a simple problem to figure out, however, it can be more complex. The power light on the blender is not lit Once you are able to get the shaft turning properly, you can put everything back together and test it. Gain access to the internal drive assembly and see if there might be some debris that is blocking the shaft from turning. The repair this you will need to unplug the based unit from the electrical outlet.Īfter you did that using a screwdriver you remove the screws hold the bottom cover and access the inside. Inside the base unit is a rubber connector that helps to couple the removable pitcher to rotating part inside the base that is connected to the motor. If you suspect that might be the problem it could be caused by a jam inside the base unit. It is possible that the blades may not be turning properly. However, if you notice that your drink in not as smooth as it should be. It is the specially designed blades that make it such a powerful blender. The blades that are located at the bottom on the pitcher are the key to the proper operation of the Ninja blender. ![]() If it still does not work, there could be a misalignment will explain that as soon as you correct the issue with the lid interlock you will be able to push the start button and it will start working again The blades are not turning properly The arrows on the lid and pitcher should line up. The owner manual has a visual description of what the lid should look like when you have it in the right position. If you see this flashing light and are not sure what it is, pull out your owner manual and it will explain what the flashing LED light indicator means. ![]() If the internal circuitry detects that the lid interlock is not completely set it will cause a flashing light indication on the operator panel of the blender. This is primarily why the lid of the Ninja blender also has an interlocking system built-in. This can lead to possible harm or make a mess if the lid is not on properly and you were to turn the blender on. The Ninja blender also includes a lid for the pitcher that allows you to put ingredients through it and into the pitcher. The lid of the pitcher was not locked tightly in place This will usually also include pictures to ensure that you are doing it correctly.Īfter looking at the manual and correcting the problem you should now be able to turn the blender on now. Inside the owner manual, you should find a section that describes the proper way to use the blender. To be sure that you have the pitcher locked in place you should consult your owner manual that came with your Ninja blender. To this end, manufacturers like Ninja have devised safeguards in order to ensure that the pitcher stays in place during operation.Īs part of this safety system, they will normally include some type of safety interlock into the base unit.īy having an interlock built-in you have to have the pitcher locked into the correct position or it will not turn on. ![]() Since a blender is a high-speed small appliance and the blades located inside the pitcher are extremely dangerous, safety is paramount. The pitcher was not locked in to the correct position Take a look at the step by step instruction in the manual and you will likely find out that you have something out of place. While it may seem unnecessary to use your manual to use something as simple as a blender, however, the Ninja is not like every other blender. If you have experienced an issue that you cannot get your Ninja blender to work you should pull out your owner manual. Click here to use the chatbox to speak with one of our technicians.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |